Hobbies And Interests
Things You'll Need
Instructions
Lay out all the pieces to the Seek and Explore: Make sure nothing is damaged or missing.
Locate and grab two of the side walls -- labeled A and B -- and the small bottom piece, labeled D. Grab side wall A and insert the bottom of it into the side of piece D.
Do the same for side wall B. Now, insert two screws into the holes on piece D; do this where the bottom of the side walls and piece D were just attached. Use the Phillips head screwdriver and tighten the screws.
Stand the assembled part upright. Grab piece E, the slide support, and insert it into the corresponding spot on piece D, press down gently, until it snaps into place.
Note: the slide support will be at a slightly angled position, which is necessary.
Locate and grab the slide, piece F. Hold the slide with both hands, and place it in-between side walls A and B, about halfway down. Locate the small, indented section on the back of the slide, and position it over the slide support. Push down on the slide until it connects properly.
Secure the slide support to the slide, and the top of the slide to the side walls. First, locate the holes on each side of the indention's edge. This will be where the slide support and the slide connect.
Insert one screw into each hole and use the Phillips head screwdriver to tighten the screws. Next, locate the small, round indentations halfway down side wall A and B. Insert each small tab on the top sides of the slide into these indentations.
Locate and grab the semicircle platform piece labeled G. Hold the platform with both hands with the flat side facing you. Insert the 2 protruding tabs into the corresponding indentations on the back of both side walls, and snap the middle part of the platform onto the slide.
Instruct an adult helper to hold the side walls steady. Grab a drill and 2 screws -- and position yourself underneath the platform. Next, hold side wall B steady, and insert one screw into the hole where the platform and back of the wall meet. Use the drill to tighten the screw. Repeat this for side wall A.
Grab the side wall piece labeled C, and the 3 rectangle pieces labeled H. Insert the side of each rectangle into the corresponding tabs on the side of side wall B.
Next, grab side wall C and position it next to the rectangle pieces you just inserted. Line up the 4 protruding tabs on the side of wall C with the 3 rectangle pieces on sidewall B, and the platform piece you just assembled.
Connect the tabs to the rectangle pieces and the platform. Push hard to make sure the wall is properly assembled.
Then, grab the screwdriver and seven screws. Insert one screw into the hole where wall C and the platform meet. Use the screwdriver to tighten the screw.
Now, insert 6 screws: Three where wall B and the 3threerectangles meet -- and three where wall C and the rectangles meet. Use the screwdriver to tighten these screws.
Locate and grab the slide labeled I. Hold the slide with both hands and place the top of it onto the platform, opposite from assembled slide F. There will be a protrusion from the platform for the slide to fit onto.
Next, grab the screwdriver and four screws. Insert one screw into each of the holes, where the top of the slide and the platform meet. Use the screwdriver to tighten the screws.
Locate and grab the small, curved piece labeled J, in addition to the screwdriver and four screws and the two wood-designed walls, labeled K and L.
Next, hold the J piece with the smooth side facing you. Locate the two protruding tabs on the opposite side.
Insert one tab into the indention on the bottom of wall K, and the other tab into the indentation on the bottom of wall L. Now, insert two screws into the holes where piece J and wall K now meet. Use the Phillips head to tighten the screw. Repeat this step for securing wall L.
Locate and grab the wedge shaped piece labeled M. This piece has a curved side, that has two protruding tabs. Hold the wedge with the point facing you. Insert one tab into the indention halfway down wall K, and the other tab into the indention halfway down wall L. Push firmly to make sure the wedge is secure.
Grab the support bar labeled O, the screwdriver and one screw. Locate the medium-sized hole on the opposite end of wall L, and the medium-sized hole on the end of the support bar. Position the support bar over the hole on wall L, and line up the holes. Insert the screw, and use the screwdriver to tighten it.
Grab the partially assembled climber with wall K and L; stand it upright with the curved J piece assembly at the top.
Position this part of the climber next to the backside of the other partially assembled climber. Next, insert the protruding tab, halfway down wall K, into the corresponding notched slot of platform G. Then, insert the end of support bar O into the corresponding hole at the bottom of wall C. Push firmly to secure.
Insert a screw into wall C and K, where the platform meets. Use the screwdriver to tighten the screw. Next, insert a screw into support bar C, where it meets with wall C, and tighten it with a screwdriver.
Gather the drill and six screws. Insert two screws each into wall A, B and C. Do this where the walls and platform G meet. Use the drill and tighten all six screws.
Attach the knotted end of the rope inside the indicated notch on the wall. Pull the rope down the side of the slide, and attach the center of it to the bottom of the slide. Continue pulling the rope from the bottom of the slide, up to the top of wall A. Attach the opposite knotted end of the rope into notch on wall A.