Hobbies And Interests
Instructions
Torso
Insert six black double-pins into a 13-hole beam. Insert them into the first two holes, the fourth, seventh, ninth and 12th holes in the rod.
Attach a blue double-ball-jointed U-shaped connector to the first two black double-pins. Slide a grey 3-hole beam with cross connectors onto the next double-pin, and a second blue U-connector onto the next double-pin. The blue pieces should fit around the grey. Push all to the bottom.
Slide a grey stud-ended rod into the 13th hole, and slide a black ball-joint socket onto the rod. Attach a blue torso plate to the two remaining pins.
Stack two 3-hole half-beams on top of each other, and slide them onto the grey pin and the neighboring double-pin. Place a grey 7-hole rod across the model so it joins the third, fourth and fifth black double-pins. Insert a black pin into the seventh hold, and a black double-pin into the fifth.
Attach a 3-hole black beam with a single plus connector to pair of black pins at the bottom. Place an orange foot piece on top of this, pointing downward, and attach it with a 3-stud long rod.
Stack two five-hole L-shaped half-beams on top of each other, and join them with a 2-stud rod at one end. Attach an orange spike to the front of this piece. Insert a grey stud-ended pin into the back of the piece, above the elbow. Make a second unit, mirrored to the first.
Place an L-shaped unit so that the elbow points outward and the free end of the L touches the shoulder of the torso plate. Join the two pieces together by inserting a grey stud-ended rod into the shoulder and sliding the L onto it. Repeat on the other side. Attach an orange spike to the end of each grey rod, so that it is parallel with the lower spike.
Attach an orange chest plate to the top of the model, to the two upright pins. Insert a black pin into the center hole on the chest plate, then cover both with an elongated blue foot piece.
Push a 4-stud rod into the bottom-most plus-shaped hole on the side of the model. Center this in the model. Repeat on the hole above with an 8-stud rod. Slide an oval-shaped plate onto these rods, pointing downward. Attach a spike, also pointing down, to the upper rod.
Plug the red head accent into the top of the skull piece. Attach the two with a 2-stud rod, then click the piece into the top-most ball joint socket. Attach the mask to the front of this piece.
Flip the model over. Insert a 4-stud rod into a black 4-way double-pin. Insert this in the third hole from the top of the black back beam.
Legs
Attach a white 2-hole half-beam to the rear half-rod of a two-toed foot plate. Attach a ball joint socket to the front half-rod.
Slide an orange spike onto a grey rod. Insert this halfway into the white beam at the back of the foot, then slide the rod through a ball-joint socket as you push all the way in.
Insert 2-stud rods into the four holes on the sides of the sockets. Attach a washer to each of the back two rods.
Place a spike upright on the work surface and insert a 2-stud rod into the back of the piece. Attach a grey 3-hole rod with two plus-shaped holes to the rod. Slide a smaller foot piece over this, and insert another 2-stud rod into the piece. Insert a black 2-hole rod, plus-hole down, into the top of the piece. Push a 3-stud rod into the piece, and place a 3-hole half-beam on the side. This makes a third toe.
Clip the toe piece to one of the 2-stud rods, and attach a second black half-beam to the other side. Attach an oval plate to either side. Plug a blue ball-jointed beam into the top of the foot.
Insert a 2-stud rod into the sides of a blue ball joint. Plug the side of an endcap into the left side rod. Attach a 2-hole rod onto the right side. Insert a 7-stud rod into the middle of this. Slide a black 4-way pin onto the long rod.
Insert a 4-stud rod into the left side, and cover it with orange tubing. Place a rod extender on the side, and attach a 3-stud rod into the side. Clip a triangle plate into the side of a blue ball joint, and attach that to the top of the two rods, the end of the triangle plate pointing to the left.
Insert a blue pin, pin-side in, into the end of a black 3-hole rod. Attach a black double-pin to the middle, and then put a 2-stud rod into the top. Attach this piece to the top ball-joint on the previous piece.
Insert a black pin into the lower right-hand beam. Attach a black 7-hole beam to the right-hand side. Click this piece onto the top of the leg.
Slide an L-shaped beam onto the back of a blue leg accent. Plug a blue pin into the back of this piece and attach an orange spike onto it. Clip this onto the side of the leg, attaching it to the 4-way pin.
Slide a ball joint onto the end of an actuator rod, and then insert that into the white actuator. Plug the ball joint into the back of the foot, and slide the top of the actuator into the back of the leg. Insert a grey rod into the piece to keep it in place.
Repeat this process, mirrored to make a second leg. Plug both legs onto the bottom of the model.
Arms
Clip a double-socket-joint beam to a ball-joint 2-hole beam. Plug a three-pronged claw piece into the bottom of the 2-hole joint ball. Make two of these units in mirror. Click these two pieces onto the middle ball joints on your model, with the claws pointing down.
Insert a black double-pin into the middle of a double-socket beam. Plug a blue pin into a black 2-hole beam. Attach this piece to the side of the socket beam. Clip a shoulder accent to the front of this piece. Click a blue ball-joint beam into the end of the socket beam.
Attach a ball-joint socket to the end of the ball-joint beam, and attach a clawed hand to the end of it.
Repeat to make a second arm, mirroring the first.
Fold the lower clawed hands up onto the back of the model. Click both arms onto the ball joint sockets at the shoulders.
Attach a length of orange hose to the 4-way pin on the back of the model, and run it out to the blue pin on the shoulder, pointed upward. Repeat on the other side.
Build the spinning blades. Attach one blade piece to the bottom of the right clawed hand, using the inner-most rod end. Attach a rod joiner to the outer rod end. Connect the other blade to the top of the hand and joiner.