Lego 8764 Building Instructions

Vezon

• 1

  Attach Vezon's back plate to his hips, a shorter black piece with two other ball joint knobs, using a black connector. Use a blue connector to attach a socket joint for his neck.

• 2

  Attach the chest accents to the back plate using black connectors.

• 3

  Use a black three-hole bar and a three-stud gray rod to attach his stomach plate to the torso.

• 4

  Connect one of the black feet to a double-ended ball-jointed leg piece, and connect a double-socketed piece to the top of that to build a leg. Attach the gray thigh guards. Make two of these legs and connect them to the torso.

• 5

  Use the same shin and thigh pieces to build an arm, but instead attach shoulder accents and a socket joint to the end for the hands. Make two arms and connect them to the torso.

• 6

  Link the chain pieces into a single chain, then connect the chain to one of Vezon's hands using a blue connector. Click a gray stud connector into the other end of the chain.

• 7

  Attach two 12-stud rods with a gray, ridged connector to build the Staff of Fusion. Attach the staff head to this.

• 8

  Slide the staff into Vezon's free hand.

• 9

  Slip Vezon's cloak onto his back, pushing it down around his neck joint.

• 10

  Attach the head, eyes and mask to each other. Click this piece into joint.

Fenrakk's Torso

• 11

  Attach two 13-hole bars to the back of a backplate using two black connectors and two black double-connectors. Us the double connectors at the top part of the plate. Point the two bars parallel to each other, toward the bottom of the backplate.

• 12

  Attach a third 13-hole bar to the middle of the backplate, pointing away from the other two, using a gray spacer-ended double-connector.

• 13

  Attach a dark gray back plate to the top of the bars, in the opposite direction to the other plate, using three black connectors.

• 14

  Attach a light gray foot plate and a light gray nose piece to the end of the single bar using two double-connectors.

• 15

  Flip the model over and attach two seven-hole bars to the ends of the 13-hole bars. Leave the last holes empty on both sides.

• 16

  Attach a red backplate to the tops of the seven-stud parts using black connectors at the tip and black double-connectors at the middle.

• 17

  Flip the model over again and attach a joint socket to the middle of the red plate using a blue connector peg. Place another blue peg in the other side of the socket. This socket becomes Fenrakk's neck.

• 18

  Attach another dark gray backplate so it lines up with the red one, and meets in the middle.

• 19

  Attach four black two-hole bars to the connector ends on the new red backplate and gray backplates, and put blue connectors inside them.

• 20

  Attach a 13-hole rod between the two dark-grey backplates. Connect a red chest plate to this bar using two black connector pegs, and a double-connector in the middle.

Fenrakk's Head and Legs

• 21

  Use a red two-stud rod to connect a ball-joint piece to the corner of a curved triangular thin bar. Connect a ball to the bottom of this piece using a three-stud rod. Sandwich these pieces between a second curved thin bar. This makes up the base of the skull.

• 22

  Attach a black three-hole bar to the head piece using a black connector and a black spacer-ended double-connector. Place a blue peg in the back end of the double-connector.

• 23

  Build and attach the upper jaw to this piece.

• 24

  Build the lower jaw, and attach that to the ball joint at the back of the skull. Clip this piece to the neck joint.

• 25

  Build the back two legs. Use the same pieces as the staff head, and a dark gray and red angled joint to make the legs, attach them to the torso with a double-jointed leg piece.

• 26

  Build the front legs, using the ball-joint piston and an arm piece to make the front of the legs. Click these into place on the body.

• 27

  Stand Vezon on Fenrakk's back, and chain his hand to an open hole on the back of the beast's neck.